Rigging and Trussing Safety: Equipment Checks, Skills and Duties
Safe event rigging is a shared responsibility, not just an equipment check. In New Zealand, rigging and trussing safety for events is subject to the Health and Safety at Work Act 2015, and businesses involved must coordinate on shared health and safety risks.
It’s understandable to focus on whether the truss, motors and connections can support the planned load. Safe rigging and trussing for events also depends on careful planning, suitable equipment and competent people following a clear plan.
This article explains how a professional rigger plans and carries out event rigging, what equipment inspections should cover, and which skills matter. It also outlines the shared responsibilities of event businesses, so you can understand what to consider before equipment is flown and the event space is occupied.
Table of Contents
Q: What certifications and inspections does rigging equipment require?
In New Zealand, safe rigging depends on matching equipment ratings and suspended weights to the capacity of venue rigging points. Inspection records, load calculations and an agreed rigging plan help determine whether an installation is suitable.
Equipment inspections and maintenance
Inspection and maintenance checks cover the condition, identification and working limits of trusses, motors, slings, shackles and other lifting equipment. Before equipment is flown, the team reviews connections, load calculations and structural integrity, removing visibly damaged gear from service.
Chain motors require annual inspection and load testing, typically at 125% of rated capacity. For overhead lifting, the usual safety factor is at least 8:1; entertainment rigging hardware for overhead suspended loads typically has a minimum design factor of 5:1. These figures describe different aspects of equipment design and use, so they aren’t interchangeable.
Each component’s working load limit (WLL) must suit its position and share of the planned load. Exceeding a component’s WLL is not acceptable. A guide also advises keeping a chain motor’s load to 75-80% of its rated capacity as a safety margin. Load calculations should include the total hanging weight, not just the truss.
Electrical planning matters too. Event teams calculate the combined load of equipment operating at the same time, including audio and lighting, and plan distribution around circuit capacity. Any backup arrangement should be included in the calculation, and emergency shutdown procedures should address electrical faults.
Approvals and engineering sign-offs
Approvals and engineering sign-offs review the proposed structure and rigging plan before installation. Venues may require an approved rigging plot, evidence of operator competency or a pre-installation review. Some require stamped engineering documents for complex or high-load installations.
For temporary event structures, distinguish the venue’s rigging approval from any council process that applies to the site or structure. An equipment inspection alone does not establish that a temporary structure or its support points are suitable. The plan should show proposed loads and rigging points, allowing the venue to assess the installation as designed.
Inspection and identification of lifting equipment
Before a lift, a professional rigger identifies each component and confirms its condition, markings and intended use. Items weighing over 20 kg should be marked with their weight and, where relevant, their centre of gravity and lifting point. Those details help the team match equipment to the planned configuration, rather than relying on appearance alone.
Inspection covers truss members and connections, motor housings, hooks, chains, slings and shackles. The team looks for visible damage, deformation, wear and missing identification, then removes equipment from service if it fails inspection, is damaged or has expired certification. Wire rope terminations should be checked by the Rigging Supervisor before first use against the appropriate part of EN13411 (1-7).
Professional riggers assemble trusses to the planned configuration, secure connections, attach lifting equipment and control the lift while keeping people clear of the load. Before operation, they review the completed structure and connections. Dismantling follows a controlled sequence that avoids leaving unsupported sections. These steps help ensure each item is secured before it is raised or removed.
A pre-event safety meeting aligns the rigging crew, production team and venue on the work plan. A site inspection identifies rigging points, access routes, working height and structural constraints. The team can then account for lighting positions, hanging equipment and anchor locations before assembly, rather than discovering conflicts during the lift.
The age and ownership history of touring equipment can also inform an inspection, particularly when a truss’s condition or previous use is unclear. A qualified engineer may need to assess structural concerns affecting the installation. For entertainment rigging, the result should be a properly documented plan that lets the crew work in sequence, with clear communication before lifting and dismantling.
Do I need a certified rigger for small events?
Event size alone does not determine the skills a lift requires. Suspended loads, venue conditions and the rigging plan all matter, so choose personnel whose training and experience match the work.
Rigging qualifications and pathways
New Zealand offers rigging qualifications through NZQA and a competency pathway for people with relevant experience. NZQA’s New Zealand Certificates in Rigging are available at Levels 3, 4 and 5. The Level 4 New Zealand Certificate in Entertainment and Event Technology includes an entertainment rigging strand.
Industry guidance recommends at least a Level 4 certificate with a rigging specialisation for independent event rigging work. Skills Active Rigging NZ also provides a Certificate of Competence pathway for people with equivalent practical experience or overseas qualifications. ETCP may appear on a rigger’s profile; consider it alongside the person’s New Zealand qualification or competency evidence, experience and the demands of the planned lift.
Fall protection and operator qualifications
Fall protection covers the controls used to manage risks while riggers work at height. Before work begins, a competent operator should understand the planned lift, equipment operation and venue access arrangements. The crew’s method should also account for suspended loads and falling objects, with suitable access and rescue planning included in the work plan.
For a small event, consider whether the work involves overhead equipment, complex load calculations or restricted access. These factors can make specialist rigging knowledge important even when the truss layout looks simple. Qualifications and demonstrated experience should match the tasks, not just the event’s audience size.
Checking a rigger’s credentials
Assess credentials against the actual rigging duties. Identify the qualification level, any rigging specialisation, and whether a Certificate of Competence recognises equivalent experience or overseas training. If a profile lists ETCP, treat it as one part of the person’s credentials, not the whole assessment.
Compare the rigger’s experience with the venue, suspended equipment and planned configuration. Ask how the team handles load calculations, work at height and changes to the plan. Clear answers help establish whether the operator can perform the specific work in line with relevant industry standards.

New Zealand health and safety duties for event rigging
Rigging and trussing safety for events in New Zealand sits within duties under the Health and Safety at Work Act 2015. Indoor plans focus on venue structure and access; outdoor plans must also account for wind, weather and shutdown thresholds. Qualified people should design, install, inspect and operate rigging in line with their competence and the work’s demands.
Health and safety duties
Each PCBU involved in an event must consult, cooperate and coordinate with other PCBUs on shared health and safety risks. This includes agreeing who manages hazards, such as a suspended lighting bar above a moving crew or audience.
For a corporate production, organisers, venues and technical teams need to share relevant plans and coordinate controls. Clear responsibilities help prevent gaps between the team planning the installation and those working beneath it. Emergency shutdown procedures should cover electrical faults, weather threats and structural concerns, so everyone knows how to respond.
Indoor and outdoor rigging conditions
Indoor rigging plans centre on the venue’s structure, rigging points, access and the positions of suspended elements. Outdoor work adds changing wind and weather, which can affect temporary structures and equipment. The plan should set wind-related shutdown thresholds and identify who can pause work.
Temporary outdoor stages and tents should be anchored and ballasted according to manufacturer specifications. Weather planning should also account for site access, power and conditions across the site. Indoor locations need their own controls, but do not face the same direct exposure to wind and rain.
Qualified rigging roles
Design, installation, inspection and operation require people competent in the tasks they perform. A suitably experienced rigger handles rigging work, while complex or high-load designs may need engineering input. Everyone involved should understand the planned loads, venue conditions and relevant safety controls.
New Zealand qualification pathways include NZQA rigging certificates and a Certificate of Competence route. The right capability depends on the work, not simply the event size. A coordinated plan for rigging and trussing safety for events brings qualified personnel, decision-makers and their responsibilities together.
For event production where rigging, weather and technical elements need coordinated planning, discuss your event production requirements.
LivewireAV: Hybrid & Livestream Events
LivewireAV supports events where in-room production and remote participation need to work together. Its Hybrid & Livestream Events offering can bring audio, visuals and camera feeds into one coordinated event plan, while Full Technical Production brings together the technical elements required for the programme. LED Walls & Projection and Audio Line Array Systems can support the audience’s viewing and listening experience.
Consider this option when planning a corporate event, conference or production with both live and online audiences. Sharing the event format, venue details and programme requirements helps shape a technical plan around the space and production needs. Rigging decisions remain part of wider safety planning, alongside equipment placement and event operations.
For a considered technical plan for your event, contact LivewireAV.
Plan your next production with confidence
Rigging and trussing safety for events is strongest when technical planning is part of the event brief from the outset. Bring production requirements, venue information and the programme together early, so the team can consider how the equipment and event setup fit the space. This creates a clearer basis for coordinating technical work with the event schedule.
The next step is to talk through your event’s requirements and how its format, venue and production elements fit together. A focused conversation can help shape a plan around the experience you’re creating, whether attendees are together in one room or joining remotely.
For a considered discussion about your upcoming event, contact LivewireAV. A clear plan gives your team a steady starting point for the work ahead.
Frequently Asked Questions
How can a professional rigging team work with venue staff or in-house AV teams?
Coordinate the event plan with venue staff and in-house AV before installing equipment. Sharing the production schedule, proposed equipment positions and access requirements helps identify clashes, such as a lighting position that blocks a venue sightline. Agreeing who communicates changes during load-in also keeps technical teams aligned, especially when the programme, room layout or equipment positions shift.
Does hiring a certified rigger cost significantly more than DIY rigging?
There’s no reliable general comparison, because professional rigging and DIY involve different responsibilities and scopes of work. The price of a professional service depends on the event requirements, equipment, venue and labour, and is provided after a quote request. DIY also leaves the organiser responsible for coordinating competent people, suitable equipment and safe execution. For overhead work, compare the full scope, not labour alone.
How do I check that a rigging or AV company is actually certified?
Check the qualifications of the people performing the rigging, rather than assuming an AV company itself holds a rigging certificate. Ask which individual is responsible and what qualification or competency evidence they hold. For work in New Zealand, relevant pathways include NZQA rigging certificates and a Certificate of Competence. Match the person’s demonstrated experience to the installation tasks and venue requirements.
How far in advance should I plan rigging for my event?
For a corporate event or gala, rigging requirements should be confirmed 2-4 weeks before load-in. This gives the event team time to align the proposed rigging plot with venue requirements, equipment positions and the event schedule. More complex installations may need engineering documents or a pre-installation review, so the plan should account for those review steps before the crew arrives on site.
What are rigging points and how do I know if my venue has them?
Rigging points are structural attachment locations used to suspend event equipment, such as trusses, lighting or screens. Their location and capacity are specific to the venue, so do not assume a ceiling fixture or visible beam is suitable. Venue staff can provide the rigging information and approved plot for the space. This lets the production plan use designated points and account for intended equipment positions.
What are shackles and how are they used in rigging?
Shackles are metal connectors used to join rigging components, such as a sling and a lifting point. In a truss installation, they form part of the connection path between the support and suspended equipment. The rigger selects a shackle suited to the connection’s configuration and load, then checks its condition and identification before use. Correct alignment matters because the connector must work as intended in the planned arrangement.



Comments